product

Dry Film PreservatIives Umiguard Z40

Umiguard Z40 is an effective broad-spectrum mildewcide algicide for the dry-film preservation of industrial products, which offer benefits including avoidance of discolouration, zero VOC content, temperature and pH stability, low-leaching, and high solubility for ease of formulation.

Chemical Name :
Dry Film PreservatIives Umiguard Z40
Application :
Efficient inhibition of mold, yeast, and algae growth, green and stable, heat-resistant, and UV resistant.
Product model :
Umiguard Z10/Umiguard Z40/Umiguard Z40 X/Umiguard Z50/Umiguard Z98/Umiguard IPBC

Inquiry now

product introduction

Umiguard Z40 is an effective broad-spectrum mildewcide algicide for the dry-film preservation of industrial products.This fine particle dispersion is specially formulated to not discolor due to interactions with various elements that can be present in some industrial formulations. In particular, soluble iron can react with zinc pyrithione the active ingredient in Umiguard Z40 and a gray-blue color may develop. By using Umiguard Z40 Antimicrobial in these formulations, reaction of iron with zinc pyrithione is suppressed.

Application:

This product is particularly effective as a single active dry film preservative, and can be used in:

-Architectural and industrial paints and coatings.

-Building materials, including floor adhesives, caulking agents, sealants, cement pastes and joint compounds.

-Building materials, including ceilings, ceiling tiles, walls and internal partitions.

The tank shall be protected against corrosion by water-based products, such as:

-Aqueous mineral and pigment slurries.

-Synthetic polymer emulsion.

-Water-based adhesive.

Product Specification:

Typical Physical Properties
Composition	A white-to off white fine particle size 52-56% solids dispersion
Physical form	Liquid
Viscosity at 25℃	5000-8000cps
PH at 25℃	8.0 - 10.5
Boiling Point	100℃
Flash point	Boils without flashing
Storage stability	Stable under normal storage conditions down to 0°C. If frozen, allow to thaw and stir well before use. The active agents are heat stable and non-volatile.
Compatibility	Avoid strong alkaline conditions,oxidising agents, reducing agents,amimes and mercaptans
Density at 25℃	1.40 - 1.45 g/ml

Specification:

Product Name	Antimicrobial Activity	Suit PH	Physical Form	Typical Dose Levels (%w/w)	Performance Effect
Umiguard Z10	Fungi (Yeast & Molds), Algae & Bacteria	4-10	Aqueous Dispersion	0.2-1.0%	Efficient inhibition of mold, yeast, and algae growth, green and stable, providing long-lasting protection.
Umiguard Z40	Fungi (Yeast & Molds), Algae & Bacteria	4-10	Aqueous Dispersion	0.1-1.0%	Efficient inhibition of mold, yeast, and algae growth, green and stable, heat-resistant, and UV resistant.
Umiguard Z40 X	Fungi (Yeast & Molds), Algae & Bacteria	4-10	Aqueous Dispersion	0.1-1.0%	Efficient inhibition of mold, yeast, and algae growth, green and stable, heat-resistant, and UV resistant.
Umiguard Z50	Fungi (Yeast & Molds), Algae & Bacteria	4-10	Aqueous Dispersion	0.1-1.0%	Efficient inhibition of mold, yeast, and algae growth, green and stable.
Umiguard Z98	Fungi (Yeast & Molds), Algae & Bacteria	4-10	Powder	0.1-0.5%	Complies with the latest green coating standards and provides surface antibacterial efficacy.
Umiguard IPBC	Fungi (Yeast & Molds), Algae & Bacteria	4-9	Powder	0.2-1.0%	Efficient inhibition of mold, yeast, and algae growth, green and stable, providing long-lasting protection.

Transportation and storage:

Stable under normal storage conditions down to 0 ° C. If frozen, allow to thaw and stir well before use. The active agents are heat stable and non-volatile.

Plastic drums: 25 kg , IBCs: 1,000 kg

Tags :

Leave A Message

categories

Featured products

Related Products

In-can antimicrobial preservative series

We are a Leading microbial control solution provider. We adhere to independent innovation and technology research and development, and protect customers' assets with our strong technology research and development and implementation capabilities. Our formulation range offers benefitsincluding long-term preservation, fast-acting disinfection, temperatureand pH stability, zero VOC content and low viscosity for ease of handing. To meet modern market requirements ( EUH 208 and EN71 regulations).our in-can biocide range includes formulations that are free fromhalogens,formaldehyde, CMT/MT and MIT.  

Dry Film Preservatives

We are a Leading dry film biocides diverse range of dry film biocides provide broad-spectrum, long-term performance from defacement due to fungi, yeast and algae.  We have both liquid and powder formulations which offer benefits including avoidance of discolouration, zero VOC content, temperature and pH stability, low-leaching, and high solubility for ease of formulation.

Marine Anti-fouling Products Series

We are a Leading microbial control solution provider. We adhere to independent innovation and technology research and development, and protectour customers' assets with our strong technology research and evelopment and implementation capabilities. We focusing on the research, development, production and services of antfouling biocides, fungicides, preservatives, mildewcides, antibacterial agents andalgaecides. Our products are widely used in paints and coatings, home andpersonal care, textiles and inks, crop protection, materialprotc-tion and healthcare fields.

Copper Umiguard powder for marine antifouling coatings

Copper Umiguard Antimicrobial powder is a viscous dispersion of Copper Umiguard Antimicrobial powder, rosin, and 1,2-Dichlorobenzene. Currently Copper Umiguard Antimicrobial dispersion is sold in other parts of the world as a marine antifouling agent.

Zinc Umiguard Dispersion Biocide for marine anti-fouling coating

We focusing on the research, development, production and services of antfouling biocides, fungicides, preservatives, mildewcides, antibacterial agents and algaecides. Our products are widely used in paints and coatings, home and personal care, textiles and inks, crop protection, material protction and healthcare fields. 

Zinc Acrylate Self-Polishing Resin

In the sea water environment, the surface of the ship is easily attached by organisms such as algae, shells, and barnacles, which not only increases the weight and resistance of the ship, but also causes corrosion and damage to the hull, while increasing fuel consumption and CO₂ emissions. Antifouling coatings are an important type of can prevent the attachment of Marine organisms, reduce the resistance of water flow and prolong the service life of ship.

In-Can Preservatives Umiguard MBS for water-based pigment paste

Umiguard MBS is effective in polymer emulsions, paints, adhesives, pigment dispersions and household products. Umiguard MBS has a non-specific mode of action which means that bacterial resistance is very unlikely to occur. Detailed information on the mode of action is available on request.

Industrial grade antimicrobial preservative Umiguard MB5050

Umiguard MB5050 is effective in polymer emulsions, paints, adhesives, pigment dispersions and household products. Uamiguard MB5050 has a non-specific mode of action which means that bacte rial resistance is very unlikely to occur. Detailed information on the mode of action is available on request.    

In-Can Preservatives Umiguard BCI for industrial waterborne coatings

Umiguard BCI is broad spectrum preservative for the protection of industrial water-based products against spoilage from bacteria, yeasts and fungi. It is a formulation of 1,2-benzisothiazolin-3-one (BIT) and a 3:1 blend of 5-chloro-2-methyl-4-isothiazolin-3-one (CMIT) and 2-methyl-4-isothiazolin-3-one (MIT) that has been specially formulated to provide good preservation at levels of 0.17% and below.   

In-Can Preservatives Umiguard CMC

Umiguard CMC is an efficient broad-spectrum bactericidal preservative, which is used to protect waterborne industrial products from infection by bacteria, yeast and mold. This product is a compound product of chloromethyl isothiazolinone and methyl isothiazolinone, which can ensure the stability of water-based coating system.. Our formulation range offers benefitsincluding long-term preservation, fast-acting disinfection, temperatureand pH stability, zero VOC content and low viscosity for ease of handing. To meet modern market requirements ( EUH 208 and EN71 regulations).our in-can biocide range includes formulations that are free fromhalogens,formaldehyde, CMT/MT and MIT.  

In-Can Preservatives Umiguard K150 for water-based coatings

Umiguard K150 is an efficient broad-spectrum bactericidal preservative, which is used to protect waterborne industrial products from infection by bacteria, yeasts and molds. This product is a compound product of chloromethyl isothiazolinone and methyl isothiazolinone, which has good compatibility for systems that are easy to demulsify and can ensure the stability of emulsion and water-based coatings.  

Printing Ink grade antimicrobial preservatives Umiguard BL10

Umiguard BL10 is a broad-spectrum preservative, which is used to protect waterborne industrial products from bacteria, yeasts and molds. Umiguard BL10 contains 10% 1,2-benzisothiazolin -3- one (BIT) in water as solvent.  

Industrial grade In-Can Preservatives Umiguard BZ

Umiguard BZ, an aqueous dispersion of a blend of 1,2-Benzisothiazolin-3-one & zinc 2-pyridine-thiol-1-oxide, is an antibacterial/anti-fungal preservative for aqueous compositions such as latex emulsions, paints, water based adhesives, aqueous slurries such as titanium dioxide and clay, and tape joint compounds  

Antimicrobial Preservative Umiguard Z50

Umiguard Z50 dispersion is an efficient and broad-spectrum fungicide that effectively protects products from infection and damage by mold, yeast, algae, and bacteria. This product is an aqueous dispersion of hydroxypyridinethiol zinc chelate, commonly known as 2-pyridinethiol-1-zinc oxide.  

In-Can Antimicrobial Preservatives Umiguard BS20

Umiguard BS20 is a broad-spectrum preservative, which is used to protect waterborne industrial products from bacteria, yeasts and molds. Umiguard BS20 contains 20% 1,2-benzisothiazolin -3- one (BIT), and low molecular alcohol is used as solvent.  

Industrial grade In-Can preservatives Umiguard BD20

BD20 preservative is a broad-spectrum bactericide, which is used to preserve industrial water-based products and prevent bacteria, yeasts and fungi from deteriorating. It is a 20% aqueous dispersion of 1,2-benzisoxazoline -3- one.

Umiguard Tralopyril for Marine antifouling biocide

In the sea water environment, the surface of the ship is easily attached by organisms such as algae, shells, and barnacles, which not only increases the weight and resistance of the ship, but also causes corrosion and damage to the hull, while increasing fuel consumption and CO₂ emissions. Anti-fouling coatings are an important type of can prevent the attachment of Marine organisms, reduce the resistance of water flow and prolong the service life of ship.

Industrial paints and coatings grade preservatIives Umiguard Z10

Umiguard Z10 is an efficient and broad-spectrum anti mold, anti algae, and antibacterial agent used to protect water-based coating films in high humidity tropical climates.2-pyridinethiol-1-oxidezinc(commonly referred pyridinethione zinc) and imidazole based aqueous dispersions.

Dry Film PreservatIives Umiguard Z40

Antimicrobial Preservative Umiguard Z40 X

Umiguard Z40X is an effective broad-spectrum mildewcide algicide for the dry-film preservation of industrial products. This fine particle dispersion is specially formulated to not discolor due to interactions with various elements that can be present in some industrial formulations. In particular, soluble iron can react with zinc pyrithione the active ingredient in Umiguard Z40X and a gray-blue color may develop. By using Umiguard Z40X Antimicrobial in these formulations, reaction of iron with zinc pyrithione is suppressed.

Dry Film PreservatIives Umiguard IPBC

Umiguard Z50 dispersion is an efficient and broad-spectrum fungicide that effectively protects products from infection and damage by mold, yeast, algae, and bacteria. This product is an aqueous dispersion of hydroxypyridinethiol zinc chelate, commonly known as 2-pyridinethiol-1-zinc oxide.

Industrial Grade Dry Film PreservatIives Umiguard Z98

Umiguard Z98 powder is an efficient and broad-spectrum fungicide that effectively protects products from infection and damage by mold, yeast, algae, and bacteria. This product is a powder of zinc pyrithione, commonly known as 2-pyridinethiol-1-zinc oxide.

Copper oxideis Cu₂O for marine anti-fouling coatings

Cuprous oxides avalence oxide of copper, bright red material, the chemical formula is Cu₂O, the relative molecular mass is 143.08. It is almost insoluble in water, in acid solution disproportionation of cupric and copper, it oxidates gradually into black cupric oxide in the wet air.  It's used as antipollution paint in the bottom of ship to kill lows forms of marine animal live; it can be also used as germicide, coloring agent in red glass. lt can also used in manufacturing kinds of nantokite, analytical regent and rectifier electroplate of electric appliances industry.

Sodium Umiguard Biocide/Dispersion for marine anti-fouling

Copper Umiguard Antimicrobial Dispersion is a viscous dispersion of Copper Umiguard Antimicrobial powder, rosin, and 1,2-Dichlorobenzene. Currently Copper Umiguard Antimicrobial dispersion is sold in other parts of the world as a marine antifouling agent.

Copper Umiguard paste/Dispersion(CPT)

Marine anti-fouling coating grade Zinc Umiguard powder（ZPT）

View All Products

Corporate Culture

Persisting on the operation concept of "Pursue honesty and quality at the same time, win hearts and profits together", the China AAB group’s people insist on the enterprise spirit of “environmental-friendly and continuous innovation, and dedicates service to all followers and customers around the world.” we have become long-term stable suppliers for many paint giants in the Europe, North American, the Middle East, Southeast Asia, Japan, South Korea and other countries and regions.

Need Help

Hot Tags

Products

Contact Us

Tel : +86 13951823978
WhatsApp : +86 13951823978
E-mail : bruce@aabindustrygroup.com
Address : No. 618, Building 01, Hongyang times business center, Jiangbei national New District, Nanjing, Jiangsu Province 210000